EAS 199B - Required Equipment

Each student in EAS 199B will use the Arduino Experimenter's Kit and software that was used in the prerequisite course, EAS 199A. Each student will also need the additional equipment listed below.

For your convenience, a list of local and on-line suppliers is provided at the bottom of this page.



EAS 199B — Required new equipment for EAS 199B

In addition to the Arduino Experimenter's Kit, each student will also need to purchase the following equipment.

1. Standard 20x4 Character LCD
LCD Panel
Minimum Quantity: One per student
Purpose: To provide visual feedback on status of Arduino programs, especially for the fish tank.
Source: PSU Bookstore -- go to the textbook desk in the basement. $18
Tutorial for wiring: Follow the LCD tutorial at Lady Ada's Arduino tutorials. Instructions on building a wiring harness to connect the wiring harness to the Arduino will be given via class notes.
John Boxall has an alternative tutorial that describes both the parallel and serial interfaces to the LCD panel. If you want to try the serial interface you will need a Serial Peripheral Interface (SPI) device like the i2c/SPI character LCD backpack from Adafruit or the Serial Enabled LCD Backpack from Sparkfun or use the Three-Wire Interface described in Boxall's tutorial.
Approximate Cost: $18-24
2. Breadboard
Breadboard
Minimum Quantity: One per student
Purpose: To provide room to implement additional circuits for controlling the fishtank. We recommend a breadboard with about the same number of holes as the one shown in the picture (840 tie-point breadboard).
Source: Various sources, including Radio Shack (catalog number 276-002 for $14.99) and Omnitron Electronics (part number BB-9831 for $2.97).
Approximate Cost: $3 - $20
3. Drill Bit Set: 1/6 to 1/4 inch
boebot
Minimum Quantity: One per team
Purpose: You need to have your own bits to drill whatever size hole you want as you complete your projects for the remainder of the year. Remember to only drill in a shop environment (not on surfaces that you are apt to damage).
Source: Various sources, including most hardware stores. You don't need an expensive, high precision, set for this class.
Approximate Cost: $5 - $15
4. DC Power Supply: 12 V, 2 Amp (minimum)
                
Minimum Quantity: One per team
Purpose: The power supply is necessary for the solenoids and heater used in the fishtank system. At least a 2A at 12 VDC capacity is needed.
Source: Various sources including Radio Shack or other electronics supply stores. Amazon has a big selection.
Used power supplies are available at used electronics supply stores. You probably have several in your closet or a junk drawer. Just make sure that the power supply meets the 12 VDC and 2A requirement.
The desktop model on the right (above) is model number PS-28 available at www.omnitronelectronics.net.
Approximate Cost: $5 - $20
5a. Project box and switches
Note that there are variations on the electrical box with switches. One solution – option 5a – is to use a project box and rocker switches. Another solution – option 5b – is to use the electrical boxes and switches common to 110 VAC household wiring.
project box
rocker switch toggle switch
One per fish tank
Purpose: The individual switches allow you separately control the power to the pump and to the electronics.
There are many types of rocker switches and toggle switches. Make sure you get an on/off type rocker or toggle switch, not a a momentary type switch.
Source: Electronic supply stores. Note that rocker switches and toggle switches can be recycled/reused from old electrical equipment. Before you throw any electronic equipment away, deconstruct it to salvage parts.
Approximate Cost: $5 to $7 for the project box and $0.50 to $7 each for the switches.
5b. Electrical box and dual switch
optional switches
One per fish tank
Purpose: The dual switches allow you separately control the power to the pump and to the electronics.
Note that there are two switches on the single switch unit. This is unlike the most common kind of light switch.
Source: Local hardware stores.
Approximate Cost: $9 for the double switch and $3 for the box and cover
6. Terminal blocks for two circuits
Terminal block  or  Euro style barrier strip
One per fish tank
Purpose: The terminal block allows connection of the input power to the always-on side of the switches. Details of installation are provided in the class notes. The terminal block also provides strain relief in case someone accidentally yanks on the power supply cord.
Source: Local autoparts stores or electronics stores like Radio Shack.
Approximate Cost: $1 to $3
7. Barrel Jack
Barrel jasck
One per fish tank
Purpose: To make it easy to disconnect the power supply so that the fish tank can be transported. Make sure the gender of your barrel jack is opposite of the gender of your power supply. In other words, if the power supply has a male plug, the barrel jack should be female, and vice versa.
Source: Local electronics stores or scavenged from used electronics, or purchased from Adafruit.com or part number 2099121 at (for a 2.5 mm jack) from www.jameco.com. or part number 159506 (for a 2.1 mm jack).
Approximate Cost: $2

Local Sources of Electronics and Electronics Equipment

The student section of the IEEE has a store that is open a few hours per day. Note that the hours are posted as a PDF file that has different names for each term. It's likely, therefore, that this link will become stale. If the link is broken, you can (probably) find the current hours from a link on the home page for the student section of the IEEE.

Here is a list of local businesses that sell electronics and tools useful for this class and all sorts of related tinkering:

Used Electronics/Surplus Electronics

Local:

Mail order and On-line

Local Hardware Stores

Some online suppliers: